Generic NEW 1 Channel 5V Relay Module 30A With Optocoupler Isolation Support High And Low Level Trigger For Arduino

i can see you must have been looking for this product Generic NEW 1 Channel 5V Relay Module 30A With Optocoupler Isolation Support High And Low Level Trigger For Arduino in nigeria. well, this product Generic NEW 1 Channel 5V Relay Module 30A With Optocoupler Isolation Support High And Low Level Trigger For Arduino is available in nigeria and you can get it via jumia.

so for those searching for where to buy Generic NEW 1 Channel 5V Relay Module 30A With Optocoupler Isolation Support High And Low Level Trigger For Arduino in nigeria online, then
CHECK JUMIA NOW

note that if this product Generic NEW 1 Channel 5V Relay Module 30A With Optocoupler Isolation Support High And Low Level Trigger For Arduino has some specifications, then you can read it on this site. but if there is non, then

CLICK TO BUY ON JUMIA

Description:

The module adopts high quality 30A relay, and the maximum load is normally open interface: AC 250V/30A, DC 30V/30A;

The chip optocoupler isolation, strong driving ability, stable performance, trigger current 5mA;

Module working voltage: 5V

Can be set up by high jumper or low level trigger.

Fault-tolerant design, the relay will not operate even if the control line is disconnected.

Power indicator (green), relay status indicator (red)

The interface design is humanized, all interfaces can be directly connected through the terminals, so it is very convenient.

Module size: 50mm x 33mm x 24mm (length * width * height)

Product net weight: 36g

There are 4 fixed bolt holes, holes 3.1mm, spacing 44.5mm x 27.5mm

Relay version: 5V

Quiescent current: 5mA

Maximum current: 190mA

Trigger current: 2-4mA

Module interface description:

1. DC+: module DC power supply positive pole (trigger terminal voltage positive).

2. DC-: module DC supply negative pole (trigger terminal voltage negative).

3. IN: signal trigger terminal (default trigger voltage is the same as power supply).

4. JD+: relay control terminal voltage positive pole

5. JD-: relay control terminal voltage negative pole

6. DC +/- and JD +/- uses jumper cap short connection, trigger terminal and relay control terminal voltage is the same.

7. Selection of high and low level trigger mode, when jumper is connected to L-terminal, IN-terminal is low level trigger, and H-terminal is high level trigger.

8. Normally closed terminal (NC): relay normally closed.

9. Public terminal (COM): common terminal of relay

10. Normally open terminal (NO): relay normally open.

Package Included:

1 x 1 Channel 5V Relay Module

CHECK JUMIA NOW

Generic NEW 1 Channel 5V Relay Module 30A With Optocoupler Isolation Support High And Low Level Trigger For Arduino

Related Searches From Other Users
where to buy Generic NEW 1 Channel 5V Relay Module 30A With Optocoupler Isolation Support High And Low Level Trigger For Arduino Online
where to buy Generic NEW 1 Channel 5V Relay Module 30A With Optocoupler Isolation Support High And Low Level Trigger For Arduino Online in nigeria
where to buy Generic NEW 1 Channel 5V Relay Module 30A With Optocoupler Isolation Support High And Low Level Trigger For Arduino Online in Kenya
where to buy Generic NEW 1 Channel 5V Relay Module 30A With Optocoupler Isolation Support High And Low Level Trigger For Arduino in Kenya
where to buy Generic NEW 1 Channel 5V Relay Module 30A With Optocoupler Isolation Support High And Low Level Trigger For Arduino Online in Ghana
where to buy Generic NEW 1 Channel 5V Relay Module 30A With Optocoupler Isolation Support High And Low Level Trigger For Arduino in Ghana

where to buy Generic NEW 1 Channel 5V Relay Module 30A With Optocoupler Isolation Support High And Low Level Trigger For Arduino in nigeria

CLICK TO BUY ON JUMIA

Be First to Comment

Leave a Reply

Your email address will not be published. Required fields are marked *